Section 13 red seal Millwright trade test
N4 electro-mechanical certificate, Siemens PLC.
5 years’ experience in heavy industry
Maintenance Process(Scheduled Preventative Maintenance)
- Receive Maintenance Schedules, plan and execute before they expire. and plan
- Inspect the tooling and determine spares and consumables requirements
- Generate Job Requisitions for scheduled maintenance work (type of repair or
- maintenance, spares, quantities, time, etc.)
- Transport tools, equipment and spares to the work site
- Isolate equipment, perform lockouts, complete the LOTO register and make the work area safe
- Complete the Contractors Permit to Work prior to contractors commencing with work on site.
- Conduct Preventive Maintenance activities
- Perform change overs in the production environment
- Count stock for a Stock Take integrity check (check spares condition during the count)
- All Scheduled Maintenance shall be recorded (Opened and Closed) to the Maintenance
- Connection system IN TIME to aid in pro-longing equipment life and prevent Unplanned maintenance.
- Housekeeping: Keep Workshop and work area clean and maintain or improve on 5S standards.
- Perform Plant start-ups. Plan plant start-up well in advance of planned production starting time to ensure the plant is ready for production. If unsure, ask.
- Track and record personal daily hours to ensure the KPA – Artisan Utilization of ≥ 75% is achieved
Mechanical Maintenance:
v>
- Perform routine maintenance
- Align machines and equipment
- Diagnose and repair faults on equipment and machinery during production/operation
- Commission and refurbish machines / equipment
- Operate and monitor a drilling machine to produce simple components
- Operate and monitor a lathe to produce simple components
- Operate and monitor a milling machine to produce simple components
- Operate and monitor a surface grinding machine to produce simple components
- Operate the Electrical Discharge Machine (EDM) to seal moulds
- Perform basic and MIG/TIG welding of metals
- Grind tools and drill bits
- Maintain mechanical equipment (indirect and direct drives, pipe systems, static seals, bearings, brakes and clutches, direct drives, dynamic seals, heat exchangers and pressure vessels, lubricating systems, pumps, conveyor systems, compressors, fluid power/pneumatic/vacuum systems, gearboxes, safety valves)
ElectricalMaintenance:
- Design and construct Single/Three Phase Circuits
- Design and Install Electrical Wire Ways
- Construct, commission and do fault tracing on low voltage reticulation networks (220Vac, 110Vac, 24DC)
- Install or replace and commission electrical equipment (lighting systems; electrical cables and conductors; earth leakage unit in a low voltage circuit; metering units or measuring instruments; low and medium voltage transformers; batteries; electrical wire ways; direct current (DC) machines three phase AC electrical circuits, machines and control gear)
- Wire and commission three phase electrical circuits
- Inspect and clean (electrical machines; enhanced safety apparatus; electrical motors)
- Test and inspect a three-phase industrial/commercial installation
- Inspect and maintain electrical equipment (electrical distribution boards, panels and enclosures; intrinsically safe apparatus; lighting systems; high mast lighting structures; batteries and battery rooms (UPS, Generator); low voltage switchgear; unit protection devices on transformers; AC or DC drive units; (DC) machines; electric power tools; three phase AC machines and control gear; AC motor control gear)
- Replace electrical equipment (electrical cables; faulty components in a distribution board; three-phase electrical motor between 5,5 kW and 75 kW)
- Fault find and repair (Domestic appliances; single phase alternating current (AC) systems;three phase voltage electrical circuits)
- Disconnect and connect electric motors
- Handle and care for electrical earthing gear and related equipment
- Joint low voltage cables
- Troubleshoot on programmable logic controllers
Fabrication:
- Mechanically cut, drill, punch and assemble fabrication materials using powered
- machinery
- Cut materials using the oxy-fuel gas cutting process (manual cutting)
- Join metals using the resistance welding process
- Weld workpiece (oxy-acetylene welding, shielded metal arc welding, gas metal arc welding, gas tungsten arc welding)
- Remove metals using oxy-fuel and air-carbon arc gouging processes
Instrumentation Maintenance:
- Construct Basic Electronic Circuits
- Install Instrument impulse lines
- Maintain instrumentation equipment (Flow; Level; Pressure; Temperature; Intrinsicallysafe apparatus)
- Carry out soldering and de-soldering procedures
